For someone who loves to shoot some random hobbyist videos, it’s somehow expensive to buy a motorized camera slider. So, I built my own. In this tutorial, we will go through each step to build your own Bluetooth-controlled motorized camera slider.

Hardware Components

Used Software

Project Overview

Today we will build a motorized camera slider that we can control it wirelessly over Bluetooth from a custom-made android mobile app. I used the “MIT App inventor” tool to make the app which gives us the ability to control a lot of stuff like the slider movement speed, traveling distance, acceleration/deceleration rate and a lot more. The mobile app is very robust, inside the app you can set your camera slider length which you are using. which means, you are free to build your actual camera slider with any length up to 10 meters without worrying about the app.

We used a NEMA17 stepper motor as an actuator so we can control how many steps do we need the camera slider to move. To control a stepper motor using the Arduino board, we need a translator that takes commands from the Arduino board and translate it to the language that the stepper motor understands. Here comes the A4988 Pololu stepper motor driver role, which gives us five different microstep resolutions (down to 1/16 step) to achieve the maximum moving accuracy and movement smoothness.

This project Designed with makeability in a fablab/makerspace/hackerspace in mind.

CAD And 3d Modeling

We used Fusion360 to design the camera slider, we chose to use very well-known, easy-to-find mechanical components that you can buy easily from almost any online or offline store no matter where you live.

We are using Openbuilds hardware to build the mechanical structure, the V-slot 2040 linear rail as a guide for the camera to move on. Two pulleys, one on the stepper motor shaft. And the other one, on an 8mm linear rail shaft on the opposite side of the slider with an open timing belt between them to convert from the stepper motor rotary motion to linear motion.

The 8mm linear rail shaft is installed between two Self-aligning Pillow Flange Block Bearings that are installed on the top and bottom plate by four M5 screws.

We are using four Delrin V-Slot solid wheels they ride down in the V-groove of the V-Slot rail to make the camera movement extremely smooth. The middle of the camera plate has a 1/4 inch diameter hole for a standard tripod screw so you can mount your camera easily.

Lastly, an enclosure for the electronics, All the camera slider parts are fixed together by m3*16mm screws and nuts.

Digital Fabrication (3d Printing)

All of the camera slider body is 3D-printed with 0.2 layer height, 20% infill, except the Camera slider left and right leg, which are printed with 0.2 layer height, 50% infill.

You can download the STL files from this link.

V-Wheel Kit Assembly

The assembly process is very easy man, come on! In the first step, we need to assemble the four Solid V-Wheels. The solid V-wheel kit comes with a rubber wheel, two bearings, two percision shims, and a lock nut.

Insert the bearing from one side of the rubber wheel and flip the wheel around, then insert one precision shim inside the rubber wheel, lastly insert the second bearing from the second face side.

Camera Slider Mechanical Assembly

First, We need to assemble the camera plate and the four solid V-Wheels. using the 9mm aluminum spacer, the precision shim, and the lock nut.

We are going to repeat the previous step with the other three wheels. in the two right wheels we’re going to use the 9mm spacer. And the other two left wheels we’re going to use the eccentric spacer with a 3mm spacer instead of the 9mm spacer.

Now, insert the camera holder plate in the V-slot profile. If you found that the plate is loose and wiggling, you can tighten the Eccentric nut until you get a solid plate.

Let’s insert two drop-in tee nuts in each end of the V-slot profile. we need to connect the V-slot profile with the right and left legs of the camera slider.

Get the two camera slider legs and push them into the V-slot profile.

bring four M5X10mm screws, and fix the two legs with the V-slot profile.

We need to install the NEMA 17 stepper motor on its plate. then, using four M3X16mm screws we are gonna fix the motor in place.

On the left leg, insert two nuts inside the left leg top nuts place.

Bring the NEMA 17 motor plate ad fix it on the top of the left leg. and, using two M3X16mm screws we are gonna fix the plate on the left leg.

To be able to convert the stepper motor rotational movement into linear movement, we need to install a GT2 Bore 5mm pulley on the motor shaft. and using the Allen key, tighten the pulley set screw to keep it in place.

Let’s go to the camera slider right leg, insert four M3 nuts in the leg nuts place.

Then, put the right leg bearings two plates on the top of the camera slider right leg.

Using four M3X16mm screws, fix the two plates on the camera slider right leg to keep them in place.

Bring one of the 8mm flange block bearings and install it on the top right leg plate. using two M5X20mm screws and two M5 nuts.

We need to repeat the previous step with the second 8mm flange bearing block to fix it on the camera slider right leg bottom plate.

Insert the 8mm linear rail shaft in the 8mm flange bearing block from it’s bottom side, ad push it to the top. Then, insert the 8mm bore pulley into the linear rail shaft and fix it by tightening the pulley’s set screw.

Checkpoint, Now we assembled all the camera slider mechanism except one thing. the timing belt. Let’s do it.

rotate the 6mm timing belt on the NEMA17 motor 5mm bore pulley. Also, on the right leg 8mm bore pulley. Lastly, tighten the belt with the camera plate.

It’s time to assemble the control board. insert the Cairo Camera Slider Arduino shield on the top of the Arduino board.

Insert the Arduino board and the Cairo Camera Slider shield inside the control board enclosure.

insert two M3 nuts inside the left leg nuts place.

install the control board enclosure to the Cairo Camera Slider left leg with M3X16mm screws.

close the enclosure box top face with two M3 screws and nuts, and that’s it!

Stepper Motor Test Control

After assembling all the parts together, We need to test it to make sure that everything is installed in its place correctly. Now, we need to connect the stepper motor with the Arduino board through the A4988 stepper motor driver and write some code to run that thing.

A4988 stepper motor driver

To control any stepper motor using the Arduino board or any microcontroller, you will need a stepper motor driver which works as a translator, takes commands from the Arduino board and translate it to the language that the motor understands.

there are a lot of stepper motor drivers out there but we will use the A4988 driver. This driver allows us to control one bipolar motor at up to 2A output current per coil, it’s very simple to interface with the Arduino board you only need two digital pins to fully control your motor step and direction, which allows you to control the maximum current output easily with an onboard potentiometer, and gives you a micro-step resolution down to 1/16 micro-step.

VMOT, GND: It’s the power connection pins for the stepper motor itself, it can be 8V-35V. In our case, we are connecting a 12V 3A power source on those pins with a 100uf decoupling capacitor to protect the A4998 board from any power spikes.

2B, 2A: the output pins for the stepper motor first coil which can deliver up to 2A.

1A, 1B: the output pins for the stepper motor second coil which can deliver up to 2A as well.

VDD, GND: Used for driving the internal logic circuitry, it can be 3V to 5.5V. It’s totally isolated from the VMOT pin.

EN: Stands for “Enable” it’s an active LOW(0V) input pin, which means when this pin pulled LOW(0V) the A4988 chip is enabled. And when pulled HIGH(5V) the A4988 chip is disabled. By default, this pin is pulled LOW(0V) . So, the chip is always enabled unless you pull it HIGH(5V).

MS1, MS2, MS3: Through these pins, you can select your motor microstepping resolution(step size). The A4988 gives you five different microstep resolutions (full step, half step, quarter step, Eighth step, Sixteenth step). By applying appropriate logic levels to these three pins we can set the motors to one of the five step resolutions.

By default, the MS1, MS2, MS3 pins have internal pull-down resistors. So leaving these three microstep selection pins disconnected results in full-step mode.

RST, SLP: The “Reset” pin is an active LOW(0V) input pin, which means when it pulled LOW(0V), all the step inputs are ignored it also resets the translator itself until you pull it HIGH(5V). The “Sleep” pin also an active LOW pin, pulling it LOW, puts the driver in the sleep mode minimizing the power consumption. By default, the “Sleep” pin is pulled HIGH(5V).

STP, DIR: The “Step” pin is responsible for controlling the number of steps that the motor is rotating, each pulse to the “Step” pin corresponds for one microstep in the direction selected by the “Direction” pin, the faster the pulses, the faster the motor will rotate. By applying logic value HIGH(5V) on the “Direction” pin it makes the motor rotate clockwise, by applying LOW(0V) it makes the motor rotate counterclockwise(it may differs from one to another according to your motor wiring with the driver).

NEMA17 Stepper Motor

Stepper motors are DC motors that can rotate in precise increments, they are used in many applications like 3D printers to align the printhead and CNC machines to control the movement of the cutting tool and this is because they are very accurate and precise.

Unlike DC motors, stepper motors are controlled by applying DC electrical pulses to their internal coils. Each pulse makes the shaft advance by one step or a fraction of step which is called “Microstepping”. So, you can control precisely how many steps or even fraction steps you want the motor shaft to move. Another great advantage of using stepper motors is that it can move very precisely and accurately at very slow speeds without even stalling.

The type of motor we are using in this project is the NEMA 17 Bipolar stepper motor. The bipolar stepper motor has two internal coils and it usually has four wires, two wires per coil. unlike the Bipolar stepper motor which has five wires. The “Step Angle” of the motor is 1.8° which indicates how much the shaft advances in each full step, the motor works on 9V but if you want to get the maximum power of it use a 12V power source.

So, by connecting the stepper motor with the A4988 stepper motor driver, we can control how many steps we need the motor to move and in what direction. Also, we can set the “microstep” mode is it full step, half step, quarter step, ….. Let’s take a look at the wiring diagram.

Wiring Diagram

As we stated before, we need to make a small check to make sure that everything we assembled before is right in its place and moving properly. Now, we will wire all the hardware together, the NEMA 17 stepper motor with the A4988 stepper motor driver to the brain, the Arduino board. And using a 12V 3A Lithium-Ion battery to feed the motors with the power it needs.

Arduino Code

AccelStepper Library Installation

The Installation is pretty simple, we need to open Arduino IDE. From the “Sketch” menu select Include Library –> Manage Libraries…

A new window should appear, search for “AccelStepper” and install the library made by “Mike McCauley”. Easy right!

After installing the AccelStepper library, you should see it in the examples menu.

I wanna make sure that the AccelStepper library is installed correctly and my stepper motor connection with the A4988 motor driver is right and my power management is fine. So, let’s write some lines of code to run our stepper motor forward and backward.

// Bounce stepper test program
// Make a single stepper bounce from one limit to another
// Copyright (C) 2020 makesomestuff.org

#include <AccelStepper.h>

#define stepPin 2
#define dirPin 3

// Define a stepper and the pins it will use
AccelStepper stepper(AccelStepper::DRIVER, stepPin, dirPin);       //create an object. the pin "2" is the step pin, "3" is the direction pin.

void setup()
{  
  // Change these to suit your stepper if you want
  stepper.setMaxSpeed(100);
  stepper.setAcceleration(20);
  stepper.moveTo(500);
}

void loop()
{
    // If at the end of travel go to the other end
    if (stepper.distanceToGo() == 0)
      stepper.moveTo(-stepper.currentPosition());

    stepper.run();
}

The code logic is pretty straightforward, we initialized an object from the AccelStepper library, we defined two constants (stepPin, dirPin) that two digital pins is used by the A4988 stepper motor driver to control the movement of the motor itself.

#include <AccelStepper.h>

#define stepPin 2
#define dirPin 3

// Define a stepper and the pins it will use
AccelStepper stepper(AccelStepper::DRIVER, stepPin, dirPin);       //create an object. the pin "2" is the step pin, "3" is the direction pin.

Inside the void setup function, we set the Max. speed of the stepper motor to 100 steps/sec. Also, we set the acceleration/deceleration rate to 20 steps/sec. lastly, we used the moveTo() function to tell the motor to move 500 steps.

void setup()
{  
  // Change these to suit your stepper if you want
  stepper.setMaxSpeed(100);
  stepper.setAcceleration(20);
  stepper.moveTo(500);
}

Inside the void loop function, we are checking if the motor reached it’s position or not. If it reached the position, it will bounce back. and if it didn’t reach it’s position yet, it will keep running.

void loop()
{
    // If at the end of travel go to the other end
    if (stepper.distanceToGo() == 0)
      stepper.moveTo(-stepper.currentPosition());

    stepper.run();
}

Camera Slider Full Wireless Control

We have done great things so far. Let’s continue! The next step after testing everything is to work on the mobile app that we will use to control the camera slider movement and send the orders to it. Also, we need to work on the Arduino code that will receive the data from the mobile app and according to these data, it will take some actions like moving the motor, changing speed, acceleration, and so on…

Building The Mobile App

To build the mobile app, I used the MIT App inventor tool that allows you to create mobile apps that run on any Android smartphone. The tool is pretty simple since you only drag and drop some pre-made code blocks to build the logic of your program, also you use some premade blocks to build the app user interface. You can access the source of the mobile app from the link down below. Feel free to edit and share, it’s open-source.

The image down below, a brief explanation for each button function and how it works.

That mobile app will communicate with the Cairo camera slider wirelessly over Bluetooth communication. So, the next step is to connect a Bluetooth module to the last circuit we built before and upload some lines of code to the Arduino board to be able to establish the communication between the mobile app and the Cairo camera slider.

Wiring Diagram

It’s time to connect all things together, previously we connected the stepper motor, stepper motor driver, Arduino UNO, and the battery together and tested the circuit and it worked fine. Now, and after building the mobile app, we need to connect the HC-05 Bluetooth module to our circuit.

To make it wireless we will use the HC-05 Bluetooth module which has wide use, it can be set as slave or master as well (unlike the HC-06 module which can work only as a slave) which means that you can make a Bluetooth connection between two different Arduino boards. the HC-05 Bluetooth module is an SPP (Serial Port Protocol) module, which means that it communicates with the Arduino board via Serial communication. You only need to connect the Tx and the Rx pins between the HC-05 module and the Arduino UNO board.

Schematic and PCB Fabrication

Man! I don’t like breadboarding a big circuit like this. So, I designed a super pretty Arduino UNO shield PCB board that keeps all my components in place without worrying about the jumper wires or even the connections. All you need to do is to place your component on the Arduino shield PCB, insert the HC-05 Bluetooth module, A4988 stepper motor driver, and the battery in their places. and install the shield on top of the Arduino board. that’s it!

I fabricated my PCB at PCBWay the quality was very good, in a few days the package arrived in Egypt safely. and I paid just 5$ for the fabrication which is amazing. The coolest thing was that I was able to check the order fabrication and processing status online on my account panel and track everything happening to my baby board like I was there inside the factory.

you can download the PCB design source files or even order the Cairo Camera Slider Arduino Shield PCB from the PCBWay website.

Arduino Code And Bluetooth Communication

#include <MultiStepper.h>
#include <AccelStepper.h>

#define stepPin 2
#define dirPin 3

bool homingPositionFlag = false;
int startupSetupFlag = 0;
bool delayedStart = false;

int incomingData = 0;
int movementDistance = 50;
long steps = 0;       //50cm rail by default @1/8 microstepping.
int microStepResolution = 0;    //4  or  16
long railLength = 0;
int sliderSpeed = 10;

AccelStepper stepper(AccelStepper::DRIVER, stepPin, dirPin);       //create an object. the pin "2" is the step pin, "3" is the direction pin.

void setup() {
  pinMode(stepPin, OUTPUT);
  pinMode(dirPin, OUTPUT);
  Serial.begin(9600);

  stepper.setMaxSpeed(10.00);        //The fastest motor speed that can be reliably supported is about 4000 steps per second at a clock frequency of 16 MHz on Arduino such as Uno
  stepper.setAcceleration(500.00);     //1600 (40%) (Medium Acceleration rate)

  while (startupSetupFlag < 3) {
    if (Serial.available() > 1) {
      unsigned int dataOne = Serial.read();
      unsigned int dataOne1 = Serial.read();
      unsigned int incomingData = (dataOne1 * 256) + dataOne;

      //**************************************************************Motor Homing Part**************************************************
      if (incomingData == 16) {      //left end homing position.
        stepper.setCurrentPosition(steps);
        homingPositionFlag = false;
        startupSetupFlag++;
      } else if (incomingData == 17) {    //right end homing position.
        stepper.setCurrentPosition(-(steps));
        homingPositionFlag = true;
        startupSetupFlag++;
      }
      //**************************************************************microstep resolution Part**************************************************
      if (incomingData == 18) {
        microStepResolution = 4;                   //50cm rail length @1/4 microstep resolution.
        startupSetupFlag++;
      } else if (incomingData == 19) {
        microStepResolution = 16;                  //50cm rail length @1/16 microstep resolution.
        startupSetupFlag++;
      }

      if (incomingData >= 1301 && incomingData <= 2300) {
        railLength = incomingData - 1300; //from raw data to cm.
        if (microStepResolution == 4) {
          steps = ((6100L * railLength) / 50L);
          startupSetupFlag++;
        }
        else if (microStepResolution == 16) {
          steps = ((25000L * railLength) / 50L);
          startupSetupFlag++;
        }
      }
    }
    //Serial.println(startupSetupFlag);
  }
  /*
   * *********** *********** **********For Debugging Purposes* *********** *********** **********
    Serial.print("rail length: ");
    Serial.print(railLength);
    Serial.print("    number of steps:  ");
    Serial.print(steps);
    Serial.print("    Homing position: ");
    Serial.print(stepper.currentPosition());
    Serial.print("    microstep resolution: ");
    Serial.println(microStepResolution);*/
}

void loop() {

  if (Serial.available() > 1) {

    unsigned int dataOne = Serial.read();
    unsigned int dataOne1 = Serial.read();
    unsigned int incomingData = (dataOne1 * 256) + dataOne;
    //Serial.print("raw data:     ");
    //Serial.println(incomingData);

    //**************************************************************Motor Control Part**************************************************
    if (incomingData == 1 && stepper.isRunning() == false && stepper.currentPosition() != 6050 && homingPositionFlag == true) {
      if (delayedStart == true) { //use millis to delay 15 seconds.
        delay(15000);     //wait 15 seconds.
      }
      stepper.setCurrentPosition(0);
      stepper.moveTo(steps);             //from end to end (@ 1/4 step).
      homingPositionFlag = false;

      /*Serial.print("rail length: ");
        Serial.print(railLength);
        Serial.print("    number of steps:  ");
        Serial.print(steps);
        Serial.print("    Homing position: ");
        Serial.print(stepper.currentPosition());
        Serial.print("    microstep resolution: ");
        Serial.println(microStepResolution);*/
    }

    else if (incomingData == 2 && stepper.isRunning() == false && stepper.currentPosition() != -6050 && homingPositionFlag == false) {
      if (delayedStart == true) { //use millis to delay 15 seconds.
        delay(15000);     //wait 15 seconds.
      }
      stepper.setCurrentPosition(0);
      stepper.moveTo(-(steps));             //from end to end (@ 1/4 step).
      homingPositionFlag = true;

      /*Serial.print("rail length: ");
        Serial.print(railLength);
        Serial.print("    number of steps:  ");
        Serial.print(steps);
        Serial.print("    Homing position: ");
        Serial.print(stepper.currentPosition());
        Serial.print("    microstep resolution: ");
        Serial.println(microStepResolution);*/
    }

    else if (incomingData == 3 && stepper.isRunning() == true) {
      homing();
    }

    //**************************************************************Set Max. Speed Part**************************************************
    else if (incomingData >= 5001 && incomingData <= 9000) {
      sliderSpeed = incomingData - 5000;
      stepper.setMaxSpeed(sliderSpeed);
    }

    //**************************************************************Set Delayed Start Part**************************************************
    else if (incomingData == 7) {   //delayed start (15 seconds) is checked "true"
      delayedStart = true;
    }
    else if (incomingData == 8) {   //delayed start (15 seconds) is not checked "false"
      delayedStart = false;
    }

    //**************************************************************Set movement distance Part**************************************************
    else if (incomingData >= 201 && incomingData <= 1200) {  //convertin from rail length into number of steps. (upto 10 meters)
      movementDistance = incomingData - 200; //from raw data to cm.
      if (microStepResolution == 4) {
        steps = ((6100L * movementDistance) / 50L);
      }
      else if (microStepResolution == 16) {
        steps = ((25000L * movementDistance) / 50L);
      }
      /*Serial.print("rail length:  ");
        Serial.print(movementDistance);
        Serial.print("      number of steps:  ");
        Serial.println(steps);*/
    }

    //**************************************************************Set Acceleration Part**************************************************
    else if (incomingData == 11 && stepper.isRunning() == false) {          //HIGH
      stepper.setAcceleration(3000);
    }

    else if (incomingData == 12 && stepper.isRunning() == false) {          //Medium
      stepper.setAcceleration(1000);
    }

    else if (incomingData == 13 && stepper.isRunning() == false) {          //Low
      stepper.setAcceleration(500);
    }

    else if (incomingData == 14 && stepper.isRunning() == false) {          //Very High
      stepper.setAcceleration(4000);
    }

    else if (incomingData == 15 && stepper.isRunning() == false) {          //Very Low
      stepper.setAcceleration(10);
    }
  }
  stepper.run();
}

void homing() {
  if (stepper.currentPosition() > 0) {
    homingPositionFlag = true;
  } else {
    homingPositionFlag = false;
  }
  stepper.moveTo(0);
}

Code Logic

We’re using the amazing AccelStepper Arduino library that provides an object-oriented interface for 2, 3, 4 pins stepper motors to control it’s movement precisely.

#define stepPin 2
#define dirPin 3

bool homingPositionFlag = false;
int startupSetupFlag = 0;
bool delayedStart = false;

int incomingData = 0;
int movementDistance = 50;
long steps = 0;       //50cm rail by default @1/8 microstepping.
int microStepResolution = 0;    //4  or  16
long railLength = 0;
int sliderSpeed = 10;

AccelStepper stepper(AccelStepper::DRIVER, stepPin, dirPin);       //create an object. the pin "2" is the step pin, "3" is the direction pin.

when you open the mobile app and get connected to the Cairo camera slider it will ask you about the micro-stepping mode that you set the A4988 motor driver to work at. it’s very important to choose the correct micro-stepping mode. The Cairo camera slider only supports the 1/4 and 1/16 micro-step resolution. If you chose a wrong micro-step mode it will affect the distance calculations causing the camera carriage to hit the slider limits. So, be careful!

      //**************************************************************microstep resolution Part**************************************************
      if (incomingData == 18) {
        microStepResolution = 4;                   //50cm rail length @1/4 microstep resolution.
        startupSetupFlag++;
      } else if (incomingData == 19) {
        microStepResolution = 16;                  //50cm rail length @1/16 microstep resolution.
        startupSetupFlag++;
      }

It sets the camera slider homing if it’s left or right side homing. the homing position, once you click on right or left side homing a specific piece of data will get sent from the mobile app to the Arduino board according to the homing position that you have chosen.

void setup() {
  pinMode(stepPin, OUTPUT);
  pinMode(dirPin, OUTPUT);
  Serial.begin(9600);

  stepper.setMaxSpeed(10.00);        //The fastest motor speed that can be reliably supported is about 4000 steps per second at a clock frequency of 16 MHz on Arduino such as Uno
  stepper.setAcceleration(500.00);     //1600 (40%) (Medium Acceleration rate)

  while (startupSetupFlag < 3) {
    if (Serial.available() > 1) {
      unsigned int dataOne = Serial.read();
      unsigned int dataOne1 = Serial.read();
      unsigned int incomingData = (dataOne1 * 256) + dataOne;

      //**************************************************************Motor Homing Part**************************************************
      if (incomingData == 16) {      //left end homing position.
        stepper.setCurrentPosition(steps);
        homingPositionFlag = false;
        startupSetupFlag++;
      } else if (incomingData == 17) {    //right end homing position.
        stepper.setCurrentPosition(-(steps));
        homingPositionFlag = true;
        startupSetupFlag++;
      }

now it sets how many steps should the stepper motor moves without hitting the camera carriage with the camera slider right or left legs. it reads and saves the rail length according to the value that the user enters in the mobile app. So, depending on the micro-step resolution that the user selected before, and the rail length I can calculate the number of steps that the motor should rotate to reach the limits of the slider rail without hitting the right or left legs.

if (incomingData >= 1301 && incomingData <= 2300) {
        railLength = incomingData - 1300; //from raw data to cm.
        if (microStepResolution == 4) {
          steps = ((6100L * railLength) / 50L);
          startupSetupFlag++;
        }
        else if (microStepResolution == 16) {
          steps = ((25000L * railLength) / 50L);
          startupSetupFlag++;
        }
      }
    }
    //Serial.println(startupSetupFlag);
  }

inside the loop function, it reads the mobile app incoming data and according to these data it takes different actions, like moving the stepper motor clockwise, moving anti-clockwise, stop and return back to the starting point, and changing the travelling speed, so on…

void loop() {

  if (Serial.available() > 1) {

    unsigned int dataOne = Serial.read();
    unsigned int dataOne1 = Serial.read();
    unsigned int incomingData = (dataOne1 * 256) + dataOne;
    //Serial.print("raw data:     ");
    //Serial.println(incomingData);

    //**************************************************************Motor Control Part**************************************************
    if (incomingData == 1 && stepper.isRunning() == false && stepper.currentPosition() != 6050 && homingPositionFlag == true) {
      if (delayedStart == true) { //use millis to delay 15 seconds.
        delay(15000);     //wait 15 seconds.
      }
      stepper.setCurrentPosition(0);
      stepper.moveTo(steps);             //from end to end (@ 1/4 step).
      homingPositionFlag = false;

      /*Serial.print("rail length: ");
        Serial.print(railLength);
        Serial.print("    number of steps:  ");
        Serial.print(steps);
        Serial.print("    Homing position: ");
        Serial.print(stepper.currentPosition());
        Serial.print("    microstep resolution: ");
        Serial.println(microStepResolution);*/
    }

    else if (incomingData == 2 && stepper.isRunning() == false && stepper.currentPosition() != -6050 && homingPositionFlag == false) {
      if (delayedStart == true) { //use millis to delay 15 seconds.
        delay(15000);     //wait 15 seconds.
      }
      stepper.setCurrentPosition(0);
      stepper.moveTo(-(steps));             //from end to end (@ 1/4 step).
      homingPositionFlag = true;

      /*Serial.print("rail length: ");
        Serial.print(railLength);
        Serial.print("    number of steps:  ");
        Serial.print(steps);
        Serial.print("    Homing position: ");
        Serial.print(stepper.currentPosition());
        Serial.print("    microstep resolution: ");
        Serial.println(microStepResolution);*/
    }

    else if (incomingData == 3 && stepper.isRunning() == true) {
      homing();
    }

    //**************************************************************Set Max. Speed Part**************************************************
    else if (incomingData >= 5001 && incomingData <= 9000) {
      sliderSpeed = incomingData - 5000;
      stepper.setMaxSpeed(sliderSpeed);
    }

    //**************************************************************Set Delayed Start Part**************************************************
    else if (incomingData == 7) {   //delayed start (15 seconds) is checked "true"
      delayedStart = true;
    }
    else if (incomingData == 8) {   //delayed start (15 seconds) is not checked "false"
      delayedStart = false;
    }

    //**************************************************************Set movement distance Part**************************************************
    else if (incomingData >= 201 && incomingData <= 1200) {  //convertin from rail length into number of steps. (upto 10 meters)
      movementDistance = incomingData - 200; //from raw data to cm.
      if (microStepResolution == 4) {
        steps = ((6100L * movementDistance) / 50L);
      }
      else if (microStepResolution == 16) {
        steps = ((25000L * movementDistance) / 50L);
      }
      /*Serial.print("rail length:  ");
        Serial.print(movementDistance);
        Serial.print("      number of steps:  ");
        Serial.println(steps);*/
    }

    //**************************************************************Set Acceleration Part**************************************************
    else if (incomingData == 11 && stepper.isRunning() == false) {          //HIGH
      stepper.setAcceleration(3000);
    }

    else if (incomingData == 12 && stepper.isRunning() == false) {          //Medium
      stepper.setAcceleration(1000);
    }

    else if (incomingData == 13 && stepper.isRunning() == false) {          //Low
      stepper.setAcceleration(500);
    }

    else if (incomingData == 14 && stepper.isRunning() == false) {          //Very High
      stepper.setAcceleration(4000);
    }

    else if (incomingData == 15 && stepper.isRunning() == false) {          //Very Low
      stepper.setAcceleration(10);
    }
  }
  stepper.run();
}

void homing() {
  if (stepper.currentPosition() > 0) {
    homingPositionFlag = true;
  } else {
    homingPositionFlag = false;
  }
  stepper.moveTo(0);
}

Cairo Camera Slider User Guide & troubleshooting

After connecting the 12V power source to the Arduino UNO board that distributes power to the Cairo camera slider Arduino shield as well, turn on the Bluetooth on your mobile, search for new devices, pair with the HC-05 device, and open the mobile app then press on the “Press here to connect with Cairo camera slider” button. It will show up the menu of the paired Bluetooth devices, select the HC-05 Bluetooth device.

After connecting successfully with the Control board, the mobile app will ask you some questions to set up some parameters. The first question will ask you about the micro-step resolution of the stepper motor driver if it’s smooth(1/4 micro-step), or very smooth(1/16 micro-step). select the mode According to the micro-stepping resolution mode that you set the A4988 driver at. If you selected a wrong mode The Cairo camera slider will not work correctly.

Then, it will ask you about the aluminum rail length that you are using in your camera slider. Enter the distance in CM. in my case I’m using a 50cm rail length.

Lastly, it will ask you about the camera carriage homing position, It’s very important to place the camera carriage on one of the two rail ends, the right end or the left end. In my case, the camera carriage is on the left end. So, I selected the left end homing.

If you started the Cairo camera slider and the camera carriage is on the middle of the rail or not on one of the two rail ends it will cause the carriage to hit the limits when it moves.

After you finish the set-up process, It will show you the parameters that you have set. And once you click OK, you will be ready to play around with your lovely Cairo camera slider.

Cairo Camera Slider In-Action

The post Arduino Motorized Camera Slider appeared first on Make Some Stuff.

Today we will learn one of the most basic concepts in the Arduino world, digital outputs, and how to apply that concept on a very cool LED.

Hardware Components

Introduction

Today we will cover the very first concept that any Arduino beginner must have to know, we will talk about Arduino digital output pins, what does digital output signal mean? and lastly, we will apply those concepts to a very cool LED blinking application.

LED! What’s it?

LED stands for “Light Emitting Diode” which is a very easy-to-use component, it’ has two terminals, lights when a specific voltage is applied across its terminals. you can use the LED as a light indicator that lights when some event happens and more

Today we will use the most common 5mm LED, there’s a lot of LED sizes like the 3mm, 5mm, 10mm this number refers to the diameter of the LED, also it has many colors like red, green, yellow, blue,…

The LED is polarized, which means that it requires a specific way of wiring to work properly.

• Long terminal: is the positive lead, should get connected to the power source positive lead
• short terminal: is the negative lead, should get connected to the power source negative lead

The Current Limiting Resistor

Resistors all its job in life is to resist the flow of electrons “current” in the circuit, you can tell that from its name.

the higher the value of the resistor the less current will flow through it, and vice versa.

the LED is actually a simple diode which after a certain amount of voltage drop on its terminals will allow all the available current (unlimited) to flow through it which is not a good idea at all. Here comes the current limiting resistor job is to choke that current flow.

There is a simple formula V = IR, where V is voltage, I is current, R is resistance. this formula is called ohm’s law. We will use this formula to get out the right resistor value, but to get the right resistor value we need to know the right V and I value to put it in the formula to get the right resistor value. To get the V value we need to know two things, the voltage source and the forward voltage (voltage drop) on the LED.

So to Let’s say that we are using a 5V power source with a red LED connected in series with it. LEDs have a characteristic called forward voltage “Vf” which means the amount of voltage that got lost across the LED terminals. when operated at a certain current which is usually 2omA. Vf primarily depends on the LED color, for example, red, orange, the yellow LED Vf is around 1.8V while green, blue, white, and UV LEDs have a Vf of about 3.3 V. So, the forward voltage “Vf” on our red LED is 1.8V.

so by subtracting the LED forward voltage “Vf”(1.8V) from the power source voltage(5V) you will get the voltage drop across the resistor that we need to calculate its resistance. and that’s exactly what we need.

Now, we need to get the I value that we will use in the formula, which is the amount of current that we need it to flow through the LED to light properly without killing it. in any LED datasheet you find a characteristic called If or Imax which is the maximum continuous current rating this often around 25mA or 30mA, which means the typical current rating is around 20mA

After getting the formula’s V and I values. Now, we are ready to calculate the resistor value easily.

Now, the 160Ω resistor value will allow 20mA of current to flow through the LED at 5V which is exactly what we need.

Wiring Diagram

The wiring is pretty straightforward, we are connecting the long leg of the LED to the Arduino digital pin 7 through a resistor, and the LED short leg to the GND. That’s it!

Arduino Code

const int redLED = 7; 			//initialize a constant named "redLED" it's value 7 which refers to the pin number which the red LED is connected to.

void setup()
{
  pinMode(redLED, OUTPUT);	    //set the GPIO pin 7 as an output pin.
}

void loop()
{
  digitalWrite(redLED, HIGH);	//output a logic level "HIGH" which means 5V on the digital pin number 7 to turn the LED ON. 
  delay(1000); 					// Wait for 1000 millisecond(s).
  digitalWrite(redLED, LOW);	//output a logic level "LOW" which means 0V on the digital pin number 7 to turn the LED OFF.
  delay(1000); 					// Wait for 1000 millisecond(s).
}

Code Explanation

const int redLED = 7;

initializing a constant named “redLED” with a value 7 that refers to the Arduino pin number 7 which the LED is connected to.

void setup()
{
  pinMode(redLED, OUTPUT);
}

the setup() function is called once at the beginning of the program when the sketch starts or after the reset of the board, we use it to initialize variables, constants, take library objects, or to write some actions that we need to execute only once at the beginning of the program.

inside the setup() function, we set the Arduino pin number 7 as an output pin, which means that we are telling the Arduino board “Yo, make the pin number 7 ready to write a 5V or 0V output at any time.”

void loop()
{
  digitalWrite(redLED, HIGH);
  delay(1000);
  digitalWrite(redLED, LOW);
  delay(1000);
}

After creating the setup() function which initializes and sets the initial values, the loop() function does precisely what its name suggests, inside the loop() function you write the main program that you need to get executed over and over again until you force shutdown your Arduino board.

inside the loop() function, we are telling the Arduino pin number 7 to write a logic level HIGH which means output 5V to the LED to light it.

Then wait 1 sec.

In the Next line, we are telling the Arduino pin number 7 to write a logic level LOW which means output 0V (GND) to the LED to turn it off.

Then wait another 1 sec. before it returns back to the first line inside the loop() function.

Troubleshooting

If your LED doesn’t take any actions:

• Make sure that your LED wiring polarity is correct, LED long lead with the positive and the short one with the negative.
• make sure that you are connecting a current limiting resistor that more than 160Ω
• Make sure that you uploaded the Arduino code to the board Successfully.

Final

CONGRATS on your very first Arduino project fam! Today we have learned how to connect an LED on the Arduino board, and how to use it. Then we blinked an LED by writing some lines of code.

The post Arduino LED Blinking Hello, World appeared first on Make Some Stuff.